TL;DR: Solar panels on a new home in Idaho can still pay off, but the math changed. The 30 percent federal credit is gone for systems placed in service after December 31, 2025, and exported power now earns far less than retail at Rocky Mountain Power. Idaho still offers an income tax deduction. Build the envelope tight first, make the house solar-ready during framing, and add panels when the numbers work for the power you will use yourself.
In this guide
- Short answer
- Are solar panels on a new home worth it in Idaho?
- What changed in 2026: tax credits and the Idaho deduction
- Your utility decides the math
- Snow, short days and Idaho winters
- Roof mount, ground mount or solar-ready only
- Code rules for solar panels on a new home
- Design decisions to make before framing
- Batteries, generators and outages
- Checklist before you commit
- FAQ
Short answer
I get asked about solar on almost every design call now. My honest answer after 20 years in construction: solar is a generation decision, and it comes after the house is designed to use less energy. If you get the walls, windows, air sealing and mechanical system right, you need a smaller array. If you skip that, panels end up paying for heat leaking out of the attic.
For most of our clients the right move is one of three: put panels on now because the roof and the budget line up, make the house fully solar-ready and decide later, or skip solar and spend that money on the envelope. I am involved in every phase of every build, and this is one of the decisions I want settled before the roof trusses are ordered, not after.

Are solar panels on a new home worth it in Idaho?
They can be. Solar works best on a new home when four things are true:
- The house runs mostly on electricity. A heat pump, induction range, heat pump water heater and an EV in the garage give the panels something to do. A house heated with propane uses far less electricity, so the array has less to offset. My notes on the heat pump vs furnace decision in Idaho cover that choice.
- You have sun to collect. A large, unshaded roof plane facing roughly south, or open ground where a rack will not shade the view or sit in a drift.
- You use the power when it is made. With today’s utility rules, power you use on site is worth more than power you send to the grid.
- You plan to stay. Payback runs on years of production. A spec home or a house you plan to sell soon rarely earns it back for you.
If two or more of those are missing, I usually tell people to make the house solar-ready and put the money into the shell. That is the same priority order I lay out in the energy efficient features worth paying for and in whether a green custom home is worth it.
What changed in 2026: tax credits and the Idaho deduction
For years the selling point was the 30 percent federal credit. That is over for systems you own. According to the IRS page on the Residential Clean Energy Credit, the credit covered qualified clean energy property installed from 2022 through December 31, 2025, and it is not available for property placed in service after that date. On a new home finishing in 2026 or later, plan as if there is no federal credit for owned panels. Leases and power purchase agreements follow different rules, and I would get a tax professional involved before signing one.
Idaho still has a state incentive. Under Idaho Code 63-3022C, an individual who installs a solar device to serve an Idaho residence can deduct 40 percent of the cost in the first year and 20 percent in each of the next three years, capped at $5,000 in any one year. It is a deduction from taxable income, not a dollar-for-dollar credit, so its value depends on your bracket. I am a builder, not a CPA. Ask your tax preparer how it applies before you count on it.
Your utility decides the math
Who sells you power matters as much as the panels. Much of the Rigby and Rexburg area is served by Rocky Mountain Power. Teton Valley is largely served by Fall River Electric, a member cooperative, and Jackson Hole by Lower Valley Energy. Each has its own interconnection application, metering rules and export credit, so the first call we make on a solar project is to the utility for that address.
At Rocky Mountain Power, the Idaho Public Utilities Commission announced in November 2025 a new time-differentiated export credit averaging 4.2 cents per kWh for customers whose systems went in after October 2020. The old approach credited exported power at the retail rate, which the commission release puts at 7 to 18 cents for residential customers. That rate stands until the utility files an update in 2028.
What that means in plain terms: a kWh you use in the house saves you the full retail price, and a kWh you export earns a fraction of that. So size the system to what the house uses during the day, not to a big annual production number that mostly flows back to the grid in July.
Snow, short days and Idaho winters
Our winters cut production two ways. Days are short and the sun sits low, and panels under snow make almost nothing. Most of a year’s output in Eastern Idaho and Teton Valley comes from spring through early fall.
A few things help. Smooth glass on a steep roof sheds snow faster than a low slope. A ground mount can be set at a steeper tilt and brushed off from the ground. And panels on a standing seam metal roof can be attached with clamps on the seams instead of drilling through the roofing, which is one more reason I like metal on mountain homes (see metal roof cost in Idaho).
The other side of shedding snow: it has to land somewhere. A full array lets go all at once. Never put an array above an entry, a walkway, a porch step or a parked car without snow guards below it. The same roof geometry questions show up in preventing ice dams, and we work them out together.
Roof mount, ground mount or solar-ready only
| Option | Best for | Snow | Roof risk | Decide by |
|---|---|---|---|---|
| Roof-mounted panels | A clear south-facing roof plane and limited open ground | Sheds on steep smooth roofs; needs snow guards below | Penetrations or seam clamps; plan with the roofer | Before trusses are ordered |
| Ground-mounted array | Acreage lots with open, unshaded ground | Steeper tilt, easy to brush off; keep out of drift zones | None on the house; trench and conduit to the panel | Before site work and utility trenching |
| Solar-ready only | Owners who want the option without the cost today | Not a factor yet | None now; roof plane kept clear | Before framing and electrical rough-in |
| No solar | Shaded lots, propane-heavy homes, short ownership | Not a factor | None | Any time |
On acreage in Teton Valley I often lean toward a ground mount. It keeps holes out of the roof, it can face true south even if the house faces the view, and it is easy to service. On a tighter lot in town, the roof is usually the only real option.
Code rules for solar panels on a new home
Idaho builds to the International Residential Code, and section R324 covers solar. The parts that shape design:
- Structure (R324.4.1): the roof must carry the panel weight plus the design snow load. Roof areas under panels are checked for dead load including the panels plus snow. In snow country that is a truss and rafter question, which is why I want panels on the drawings before the truss order. My post on snow load for a Teton Valley home covers the numbers.
- Fire classification (R324.4.2): rooftop panels must carry the same fire classification as the roof assembly. That matters on wildfire-exposed lots; see wildfire resistant construction.
- Firefighter pathways (R324.6.1): at least two 36-inch pathways from eave to ridge on separate roof planes, with at least one on the street or driveway side. Roofs at 2:12 or flatter are exempt.
- Ridge setbacks (R324.6.2): 18 inches on both sides of the ridge when the array covers up to 33 percent of the roof plan area, 36 inches above that. With an NFPA 13D or P2904 sprinkler system, the 18-inch setback stretches to arrays up to 66 percent (R324.6.2.1). More on that in do I need fire sprinklers in a new Idaho home.
- Below egress windows (R324.6.2.2): no panels on the roof below an emergency escape opening, and a 36-inch pathway to it. That ties straight to egress window requirements.
- Ground mounts (R324.7): designed under R301, with fire separation distances set by the local jurisdiction.
These rules eat roof area. A roof broken up by dormers, valleys and vents can lose half its usable space once pathways and setbacks are drawn in. If solar matters to you, the roof design has to start there.
Design decisions to make before framing
Whether you install panels now or later, these cost little during design and framing and a lot after drywall:
- One clean roof plane. Keep plumbing vents, flues, exhaust fans and skylights off the plane that faces south. Route them to the north side.
- Truss design for panel weight. Tell the truss designer which planes will carry an array.
- Conduit. Run an empty conduit from the attic or roof to the electrical room, and a second for a battery or ground-mount feed if there is any chance of one.
- Panel space. Leave breaker space and capacity for a solar backfeed and a future battery. My post on electrical panel size for a new home explains why I size up.
- Wall space. Hold a spot in the garage or mechanical room for an inverter, disconnects and a battery.
- Surge protection. Inverters and batteries are expensive electronics; whole house surge protection is cheap insurance.
This is part of how we lock a fixed price after design. If solar is in or out, it is on the drawings and in the contract, not a change order halfway through framing.
Batteries, generators and outages
A common surprise: a standard grid-tied solar system shuts off when the grid goes down, for the safety of line crews. Panels alone do not keep your lights on in a storm. To ride through an outage you need a battery with the right controls, a generator, or both.
For short outages on an all-electric house, a battery can cover the essentials quietly. For multi-day winter outages on a rural lot, a generator is still the more reliable answer. I go through sizing in backup generator sizing for an Idaho custom home.
Checklist before you commit
- Get the envelope and mechanical design set first, then estimate the home’s electric use.
- Call the utility for the address and ask for its interconnection steps and current export credit.
- Pick the location: roof plane or ground, and check it for shade, drifting snow and the view.
- Lay out code pathways, ridge setbacks and egress windows on the roof plan.
- Put panel loads on the truss order and conduit on the electrical plan.
- Ask your tax preparer about the Idaho deduction, and assume no federal credit for owned systems.
- Decide now or later. If later, build it solar-ready and write that into the scope.
If you are building in Teton Valley, Rigby, Rexburg or anywhere in Southeast Idaho and want to work through whether solar belongs on your house, we are glad to help. Learn more about how we build on our Teton Valley custom home builder page, call us at (208) 520-0636, or reach out here.
FAQ
Are solar panels on a new home in Idaho worth it in 2026?
Sometimes. They make the most sense when the house is all-electric, the envelope is tight, you have an unshaded south-facing roof plane or room for a ground mount, and you plan to stay long enough to recover the cost. Since the federal credit ended and Rocky Mountain Power now credits exported power at a lower rate, the case rests on the energy you use yourself, not on selling power back.
Is there still a federal tax credit for solar on a new home?
Not for a system you own. The IRS says the Residential Clean Energy Credit is not available for property placed in service after December 31, 2025. Leased systems follow different rules, so talk to your tax preparer before you sign anything that promises a credit.
Does Idaho offer a solar incentive?
Yes. Idaho Code 63-3022C lets an individual who installs a solar device to serve an Idaho residence deduct 40 percent of the cost the first year and 20 percent in each of the next three years, with a cap of $5,000 in any one year. It is a deduction from taxable income, not a credit, so confirm how it applies to your return with a tax professional.
Will snow stop solar panels from working in Teton Valley?
Snow cuts winter production, and short winter days cut it more. Panels on a steep, smooth roof often shed snow after a storm, and a ground mount can be tilted steeper and brushed off. Expect most of your production from spring through early fall, and plan snow guards below any array that sits above a door, walkway or driveway.
Should I make my new home solar-ready even if I skip panels now?
Yes, in most cases. Running a conduit from the attic or roof to the electrical room, leaving space in the panel, keeping one roof plane clear of vents, and telling the truss designer to plan for panel weight costs little during framing and a lot more after drywall.

